European smart utility meter gateway is first to combine M-Bus, cellular IoT and LoRaWAN all running off a single Nordic nRF9160 SiP


M-Bus (which is short for ‘Meter-Bus’) is a European short-range standard for the remote wireless reading of water, gas, electricity, heat, and other consumption meters. By combining cellular IoT and LoRaWAN in a single gateway, European utility and buildings management customers are not restricted to any one LPWA wireless technology and can “mix and match” depending on local network availability and wireless signal coverage

Nordic Semiconductor today announces that German industrial IoT solutions specialist, Lobaro, is using a Nordic multi-mode NB-IoT/LTE-M nRF9160 SiP in its Wireless M-Bus Gateway to provide Low Power Wide Area (LPWA) networking of European M-Bus utility meters using NB-IoT or LoRaWAN or a combination of both. Lobaro says data uploading to the Cloud is done using NB-IoT due to its larger payload capacity (1600 versus 243 Bytes) along with over-the-air updates of devices installed in the field that Lobaro says is easier to do with cellular IoT.

The Lobaro Wireless M-Bus Gateway (wMBus) is said to be a simple to use, cost- and energy-efficient device that receives, caches, and finally forwards metering consumption data from up to 250 Wireless M-Bus enabled utility meters to the Cloud.

Lobaro says any metering device conforming to the 868 MHz Wireless M-Bus standards (EN 13757-4) uses low-power short-range FSK radio modulation to broadcast consumption data. The wireless range is typically only about 50m using this traditional technology. The Lobaro Wireless M-Bus Gateway claims to extend this range by collecting the short-range data and then uploading it to the Cloud using long-range NB-IoT. A firmware variant with an additional upload path via LoRaWAN networks is used to add this additional capability. This unique feature of combining two LPWA network wireless technologies in a single gateway enables each to be used as a fallback if, for example, no local NB-IoT or LoRaWAN network is available at the place of deployment.

All the heavy lifting is done by the Nordic nRF9160 SiP so if you look at PCB inside our Wireless M-Bus Gateway there are very few additional components required
Tobias Kaupat, Lobaro

Metering data is sent to the Lobaro Platform, were it gets parsed, displayed and made available for further processing. Because most Wireless M-Bus telegrams are encrypted, the Platform allows adding decryption keys for individual meters, so that the data can be decrypted by the Platform. It is also possible to use the Lobaro Wireless M-Bus Gateway without the Platform and connect it to a standalone backend as long as it is capable of parsing and decrypting wMBus telegrams.

“Cellular IoT and LoRaWAN are regarded by a number of customers as complementary wireless technologies in the utilities smart meter sector,” comments Theodor Rohde, Managing Director of Lobaro. “This is because LoRaWAN came to market first and so there are a lot of existing installations where customers don’t want to be forced to have to make a wholesale change to cellular IoT. At the same time, they don’t want to be limited to just using LoRaWAN either and having the option of both yields greater design flexibility and reliability in areas of limited coverage or poor signal strength.”

In operation the Lobaro Wireless M-Bus Gateway sits close to where the utility meters are located, either in a basement or on every two or three floors of a large apartment building. Lobaro is currently running their in-house developed LoRaWAN and Wireless M-Bus stacks on the nRF9160 SiP’s embedded Arm® Cortex®-M33 processor plus 1 MB Flash and 256 KB RAM. Lobaro also supplies and maintains every last piece of the smart meter reading solution from hardware to device management and configuration to firmware. All a customer is said to need is a high-level Cloud platform.

“All the heavy lifting is done by the Nordic nRF9160 SiP so if you look at PCB inside our Wireless M-Bus Gateway there are very few additional components required,” adds Tobias Kaupat, CTO at Lobaro. “This also enabled us to get the size of the unit down to 122 x 82 x 55mm, including the use of one “D”-sized primary 3.6V (14.5Ah) battery that because of the low power characteristics of the Nordic nRF9160 SiP can achieve a battery life of up to 10 years when sending metering data once every day.”