Eng 日本語 한글 繁體 简体

nRF9160 DK Development kit

Cellular IoT development kit for LTE-M, NB-IoT, GNSS and Bluetooth LE

The nRF9160 DK is an affordable, pre-certified single-board development kit for evaluation and development on the nRF9160 SiP for LTE-M, NB-IoT and GNSS. It also includes an nRF52840 board controller that for example can be used to build a Bluetooth Low Energy gateway.

It has a dedicated LTE-M and NB-IoT antenna that supports a wide range of bands, to operate globally. LTE bands B1, B2, B3, B4, B5, B8, B12, B13, B14, B17, B18, B19, B20, B25, B26, B28 and B66 have been certified. See the nRF9160 certifications page for more details.

A dedicated patch antenna for GNSS, and a 2.4 GHz antenna to be used with Bluetooth LE are included on the board. SWF RF connectors are available for the LTE-M/NB-IoT and 2.4 GHz antennas. A connector is also available to attach an external GNSS antenna.

All GPIOs and interfaces (SPI/TWI/UART), are available via connectors. The kit is Arduino Uno Rev3 compatible, meaning it can be easily interfaced with external device shields.

User-programmable LEDs (4), buttons (2) and switches (2) are available to easily give input and get output. The nRF9160 DK has both a 4FF SIM card slot and an MFF2 SIM footprint, to support both plug-in and soldered (e)SIMs. It is bundled with a eSIM card from iBasis preloaded with 10 MB.

Programming and debugging is enabled through the Segger J-Link OB, which also supports external targets. The nRF9160 DK is supported by a full suite of development software and tools. All free to download and use commercially.

nRF Connect SDK includes everything needed to get started, application layer protocols, examples, peripheral drivers and more. The kit can easily be connected to our cloud solution, nRF Cloud. The nRF Link Monitor tool located in nRF Connect for Desktop provides an AT command interface that enables you to test your link, and extract information about the network.

The nRF9160 SiP and nRF9160 development kit are now in production and are suitable for full end-to-end sensor to cloud development. We’re still developing features and optimizing performance.

See the nRF9160 certifications page for details on certification, LTE bands and security supported. 

PDF IconDownload nRF9160 DK product brief (PDF)

PDF IconDownload nRF9160 DK product brief Simplified Chinese (PDF)

Ask us about this
Key features
  • Global LTE-M/NB-IoT antenna
  • GNSS antenna
  • Arduino Uno form factor
  • Supports Bluetooth LE
  • 4 LEDs user-programmable
  • 2 buttons user-programmable
  • 2 switches user-programmable
  • SEGGER J-Link OB Debugger with debug out support
  • UART interface through VCOM port
  • USB connection for debug/programming and power
  • Bundled with an eSIM card from iBasis preloaded with 10 MB 
Documentation
Downloads
CE Certification

Getting started

with nRF9160DK

  1. Go to www.nordicsemi.com/nrfconnect 
  2. Download & Install nRF Connect for Desktop
  3. Open Quick start

Important: Mac/Linux users need to manually install Jlink beforehand, this can be done by installing nRF Command Line.

Cellular Connectivity

To connect the nRF9160 DK to either LTE-M or NB-IoT networks in your region, you need a IoT enabled SIM card.
The iBasis card included in the kit has coverage in most regions (download the coverage map for more information).

If the iBasis SIM does not have coverage in your region, please contact your local Regional Sales Manager for advice or your local network operator to purchase a local IoT-enabled SIM.

Explore DevZone