- nRF24L01+ compatible RF Transceiver
- Worldwide 2.4GHz ISM band operation
- Up to 2 Mbps on air data rate
- Enhanced ShockBurst^TM hardware link layer
- On air compatible with nRF24LE1, LU1, L01+, L01, nRF2401A,
02, E1 and E2
- Low cost external ±60ppm 16MHz crystal
- Full speed USB 2.0 compliant device controller
- Up to 12 Mbps USB transfer rate
- 2 control, 10 bulk/interrupt and 2 ISO endpoints
- 512 bytes dedicated USB endpoint buffer RAM
- Software controlled on-chip pull-up resistor for D+
- Integrated PLL for full-speed USB operation
- On chip Voltage regulators, 4.0 to 5.25V supply range
- Enhanced 8-bit 8051 compatible microcontroller
- Reduced instruction cycle time
- 32-bit multiplication-division unit
- 16 or 32 Kbytes on-chip flash memory
- 2 Kbytes SRAM
- 6 general purpose digital input/output pins
- Hardware SPI and UART
- 3 16-bit timers/counters
- 128 bit AES encryption/decryption co-processor
- Supports flash programming and upgrades over USB
- Supports nRFprobe and FS2 hardware debuggers
- Compact 32-pin 5x5mm QFN package
- nRFgo compatible development kit

- Compact USB dongle for wireless peripherals
- A low cost solution is enabled by high level of integration
and a minimum number of low cost external components
- Power directly from USB power removing the need for
external voltage regulator
- Complete development platform for reduced development
cycles and risk

Compact USB dongles for wireless peripherals:
- Mouse, Keyboard, remote control
- Advanced media center remote controls
- Game controllers
- Intelligent sports equipment
- Toys

A single chip solution with the nRF24LU1+
The nRF24LU1+ is a unique single chip solution enabling ultra compact USB dongles for wireless peripherals. By integrating an USB 2.0 compliant device controller, 8 bit application microcontroller and a nRF24L01+ compatible 2.4GHz RF Transceiver it supports a wide range of application including PC peripherals, sports accessories and game peripherals. With air data rate of up to 2 Mbps combined with full speed USB, supporting up to 12 Mbps, the nRF24LU1+ meets all the requirements of applications with stringent performance requirements such as wireless mouse, game controllers and media center remote controls with displays.

Highly integrated solution
Compact 5x5mm package, low cost external BOM
In addition to the main blocks the nRF24LU1+ integrates other critical functionality, saving cost and board space. Internal memory removes the need for an external EEPROM. An internal voltage regulator enables the chip to be powered directly from the USB bus; it does not require an external voltage regulator. With a fully integrated RF synthesizer and PLL for the USB no external loop filters, resonators or VCO varactor diodes is required. Only 1 low cost ±60ppm 16MHz crystal plus passives for ESD protection, decoupling, antenna matching circuitry is required. nRF24LU1+ enables true single chip USB dongles.

nRFgo a complete development platform
For firmware and hardware engineers
The nRF24LU1+ is supported by a complete development platform enabling designers to easily develop hardware and firmware for the chip. The platform comprises two key elements: the nRFgo Starter Kit and the nRF24LU1+ Development Kit. Both are required to get started with nRF24LU1+ development.

The nRFgo Starter Kit provides a generic development platform for all nRF devices providing motherboards with sockets for the nRFgo development kit modules as well as the nRFgo Studio evaluation and management PC application. The nRF24LU1+ Development Kit comes in only one version, fitted with nRF24LU1P-F32Q32 (32 kbytes flash memory) devices. The kit include nRFgo compatible nRF24LU1+ radio modules, a production ready USB dongle, complete Software Development Kit (SDK) and the nRFprobe hardware debug utility.