- What can I do to get rid of errors about --asm and --interleave when compiling nRF51-projects?
- Why does Keil crash at random times when using the nRF51 kits after upgrading to J-Link 4.56?
- Why do I get “Error: Flash download failed – Cortex-M0” when downloading a project from Keil?
- Why does my program not run and the debugger shows the code being only 0xFFs?
- Why can Master Control Panel not find my Master Emulator Dongle?
- Why can I not find my Bluetooth Low Energy devices from iOS’s Bluetooth Settings?
- Where can I find drivers for nRF9E5/nRF905/nRF24LU1 Evaluation Kit for Windows 7 64-bit?
- When will Nordic Semiconductor obsolete/End-of-Life device X?
- Why does my iPhone immediately disconnect from my nRF8001/nRF8002?
- Are there any license fees for using your products?
- Can I use a WLAN or Bluetooth antenna together with the Nordic 2.4 GHz nRF devices?
- Do I need an MCU or EEPROM together with the nRF24Z1?
- Do I need Keil CA51 or PK51 to develop with the nRF24LE1 and nRF24LU1P?
- Do I need to tune the antenna in my design to acheive 50 Ohm impedance?
- Do you have a printed 868/915MHz loop antenna layout available for the nRF905/nRF9E5 device?
- Do you have any frequency hopping example code?
- How do I connect the EEPROM to the nRF9E5/nRF24E1 when I also want to do in- circuit programming?
- How do I control a DAC on the nRF24Z1 ARX?
- How do I make the nRF24L01 output a fixed carrier?
- How do I obtain the price on your products?
- How do I program the nRF24LU1 and nRF24LE1 flash in production?
- How should I connect the quarter wavelength printed monopole antenna, documented in your white paper, to the nRF device?
- How to choose an address?
- How to configure the nRF24L01/nRF24L01+ to RX mode?
- How to exchange data between ARX (nRF24Z1) and ATX (nRF24Z1) when using two MCU's?
- How to measure Bit/Packet Error Rate (BER/PER) on the nRF24L01?
- How to set RTC wakeup with the nRF24E1?
- How to set wakeup from powerdown mode with nRF9E5?
- How to setup deep sleep on the nRF24LE1?
- How to setup memory retention timers on, on the nRF24LE1?
- How to setup register retention mode on the nRF24LE1?
- How to setup register retention mode timer on, on the nRF24LE1?
- How to setup the UART on the nRF24LE1?
- How useful is Carrier Detect (CD) on the nRF24L01?
- I am not able to debug or program my nRF device from Keil, what might be the problem?
- I changed the configuration on the nRF24Z1 but it is not enabled, why?
- I have a question that is not answered here, where can I direct my question?
- I need to know the lead time on your products, where can I obtain that information?
- I want to make a new product with the nRF401, nRF403 or nRF903
- I want to use a 4 layer pcb, I intend to run signal/gnd/pwr/signal, what is the best to do around the nRF? - should I make ground planes on the outer layers or not?
- I want to use an antenna with an impedance different from 50 ohm. How can I match this antenna to the nRF device antenna port?
- Is it possible to have a single nRF24Z1 as a transmitter, and have 2 nRF24Z1s configured as receivers?
- Is the nRF2401A drop-in compatible with the nRF2401?
- Must the ADC input pins on the nRF24E1 and nRF9E5 be connected to a defined level when not in use?
- Should we connect the die attach pad on the QFN package?
- The firmware upgrade failed on my nRGgo Motherboard. How can I restore it?
- What do I need to start developing with the nRF24LE1?
- What information is available?
- What is the difference between nRF2401 and nRF2401A?
- What is the purpose of the evaluation kit you offer?
- When I use the Keil license included in the Development Kit to get a License ID Code from Keil, it says: "Expired: Mar 2008." What should I do?
- Where can I find example code for the device?
- Which power down mode should I use with the nRF24LE1?
- Why are some of the product specifications marked "preliminary?"
- Why should I use the Ext32K clock with the nRF24AP1 and nRF24AP2 devices?
- Why should I use the recommended layout for the antenna matching network?
- How to configure the nRF24L01/nRF24L01+ to TX mode?
- The nRF24L01 Product Specification V2.0 looks very different from nRF24L01 Product Specification V1.0, why?
- Revision 2.0 of the nRF24L01 Product Specification include some previous undocumented features. Has the nRF24L01 chip been changed?
- What previous undocumented features became documented in revision 2.0 of the nRF24L01 Product Specification?
- I have a design with the nRF24L01. Do I need to re-qualify my design because of the new information in revision 2.0 of the nRF24L01 Product Specification?
- Do I need to get a new regulatory approval on my nRF24L01 application if I replace the nRF24L01 with the nRF24L01+?